1.888.673.9555
e-mail

Trailers for Sale

9 Racing Team Race Trailer
Fabricate and supply 56’ long custom Performance Trailer shell (3) axle air ride suspension with special interior wheel well clearance of 68” .100”thick smooth aluminum side bent sheet construction 13’6” tall overall height at full ride travel 32” drop straight floor with 16” tall wheel boxes (138” inside height) 106” height clearance at fifth deck area 108” long fifth deck length for truck tandem clearance Hydraulic level legs with exterior controls behind locking access door Special configured Alcoa polished wheels with stainless hub / lug nut covers 3/16” aluminum smooth floor with countersunk steel monobolt fasteners ABS break system with warning light at rear driver’s side 102” exterior overall width 4” steel cross members with 12” centerline spacing Aluminum non-slotted wall logistics posts at 16” centers Reinforce rear of trailer for electric screw lift gate Custom fender treatment at wheel openings (painted hoop style fenders) 36” wide single swing access door with interior / exterior latch Single piece .040” aluminum sheet roof with aluminum bows at 12” centers Special air ride raise / lower valve with plumbing (in truck dash controls) Undercoat trailer fifth deck underside and trailer underbelly Install Performance Trailers electric screw operated lift gate AC operation with 220 volt multi-speed step motor with brake *Power unit location at rear to be determined Wireless remote control operation with spare controller Aluminum lift gate platform with aluminum smooth load surface *High impact rubber tile (black) on platform (see option #4) Type to be large square radius corner type Gradual transition at rear of platform for loading low slung cars Smooth aluminum paintable rear gate skin with single center seam 24” lightweight aluminum extension with in motion latch *This too will be covered in high impact rubber tile Steel formed upper gate header with LED clearance lights LED flush mounted stop / turn / clearance lights at lower exterior of platform Colored chain covers for closing and support chains All weather seal at gate surround (no roll-up door) *Modify gate to have system for motor change-out Includes frame reinforce and fabricated assembly tool Fabricate and install solid second level decking system 47’ length by full width Set deck height at 60” from top load surface to main ceiling underside 36” square access hatch area with door at top *this door will be located at front right corner of deck Aluminum framed construction with 3/16 smooth aluminum top load surface (3) rows of full length Ancra style aircraft tie down track *full length rubber track cover White aluminum lined under skin with no exposed fasteners (5) fluorescent four tube light fixtures with side door switch Trim outer perimeter of deck with fabricated white aluminum Silicone seal top load surface perimeter seams Supply and install diesel generator at nose of trailer 20kw operation with 100% duty cycle custom sound attenuation treatment with premium anti-vibration isolators remote start panel at trailer interior 40 gallon fuel storage with level gauge Steel framed enclosure with large locking access doors Vertical side enclosure exhaust exit Electric fresh air intake / hot air exhaust Service kit for 150 / 300 / 450 hours service intervals Install custom electrical / lighting package (2) exterior mount 30 amp receptacles for car heaters Possible locate these inside trailer rear door opening (3) duplex 120 volt weatherproof exterior receptacles Possible locate these inside trailer rear door opening (2) upper 300 watt quarts load lights at interior ceiling pointed out rear door (2) under second deck mount 300 watt quarts lights pointed out rear door These will be detachable and able to be removed to clip on outer end- of lift gate (5) fluorescent four tube lights located equally spaced at second level deck (6) corner mount two tube fluorescent lights at main ceiling area Fluorescent lights to be T-8 type (6) ceiling mounted 12 volt lights with wall switch (4) lower deck mounted 12 volt lights with wall switch (4) interior duplex 120 volt electrical receptacles Master electrical control panel at side door area with gauge package 100 amp electrical distribution panel with breaker switches Electrical hardwire with breaker switch for air compressor system All light / control systems to be located just inside side door All wiring is THHN stranded core shielded type with grommets at chassis 50 amp electrical shore power connect with 20’ cord length Customer may have 30 amp plug installed Automatic switch from shore power to generator power control * Supply and install HVAC in lower rear trailer section Area to be cooled / heated approximately 47’l x 73”h- X 99” wide Wall mount register Component mount thermostat Locate condenser at front generator storage box Supply and install 3hp two stage air compressors with compressed air tank (4) exterior quick couple receptacles at underside of trailer (2) quick couple receptacles at interior Water separator / filter regulator with easy access drain 20 gallon compressed air storage tank Plum locations for nitrogen bottle air feed (1-inlet / 3-outlet quick couplers) Fabricate and install aluminum wall ladder for second level deck access Locate at wall by front fifth deck entrance Non-skid step rungs Mount low profile to wall Design / fabricate / install rear collapsible partition wall Aluminum frame construction with collapsible design Can be moved against wall for storage while trailer is in motion Double slide doors with see-through one-way clear windows Locking latch with center pin Fabricate and install partition wall at front fifth deck area Laminate exterior / interior finish *this wall will be full height 32” wide Sliding pocket door with privacy latch hardware *locate far right at partition Trim at edges to be fabricated white aluminum Insulate trailer interior and line nose / walls and ceiling 3” thick steel building style insulation Line ceiling with white aluminum Line walls with white aluminum Line interior nose with white aluminum Install special wall anti-rub pieces at various wall locations for customer – equipment tie downs Install (2) rows 120” long tie down track pre-determined wall area locate at wall above second level deck Install (2) rows full length tie down track to lower floor walls * Install customer supplied / shipped aluminum cabinets 2-at wheel box locations 2-aluminum cabinets located at fifth deck area * Supply and install (2) aluminum fold-down workbenches Customer to determine location * Fabricate and install custom aluminum storage assemblies 1-front axle rack for (4) axles (locate at fifth deck area) 1-three row sections of aluminum shelf assembly Size to be approximately 36”w x 100”long 1-(2) rear end storage bracket assemblies Supply and install aluminum Ancra tie down track at main trailer floor Two rows full length of 47’ main floor supply rubber slip in cover Top surface install with mono-bolt application Customer will advise of location for install Includes (18) tie down car assemblies with 5000# rating Fabricate and install aluminum roof mount observation deck Aluminum diamond plate step surface Size to be 10’ long by full trailer width Aluminum fabricated radius tube folding hand rails (2) aluminum fabricated lightweight ladders with wall storage brackets 1-lto be from ground to gate platform 1-to be from lift gate platform to roof area access Paint exterior of trailer gloss white PPG material with warranty card Includes upper and lower aluminum extrusions Paint all lift gate components including interior door thresholds Paint interior of side door Paint nose area including generator storage box Roof to be taped off to prevent overspray Silicone seal all seams and edges with paintable sealer Supply extensive owners / operators manual Also includes full training on trailer/ components operations at time of delivery Options Requested (pending approval) Supply auxiliary power supply connection for lift gate To be used in case of generator failure Install 50 amp connect at exterior roadside Include 50’ “jumper cord” with plug ends Isolated transfer switch Supply and install high impact rubber tile floor at main trailer floor area includes front fifth deck floor as well customer to choose color and design pattern fabricated trim at floor / wall area Supply and install high impact rubber tile floor at second level deck Customer to choose color and design pattern Fabricated trim at floor / wall area Supply and install high impact tile at liftgate load surface Apply over smooth aluminum material Supply and install quick couple air receptacle at upper floor Locate per customers direction Includes shop feed receptacle inlet Supply and install rear trailer decals per customer photo (1) reflective “9” with “Nine Racing, Inc” (1) “Team ASE” (1) “Oakley” (3) drivers names with # (1) “Weld Racing” (1) “Snap On” (1) “Beast” (1) “Performance Racing Industry” (1) "Toyota” (1) “This Vehicle Makes Wide Turns” (1) “Earl’s Performance” Supply (24) ratchet tie down assemblies Install (2) 120volt electrical interior duplex wall receptacles- at interior front fifth deck Asking Price: $316,500 Call or Email with questions. Performance Trailers, Inc. 3105 Airport Drive Madera, Ca 93637 Phone 559-673-6300 Fax 559-673-1948

Project Portfolio | About Performance Trailers | Trailer Options | Trailers for Sale | Contact Us

© All Rights Reserved - Performance Trailers, Inc. 2007